Szabványkereső

Hivatkozási szám, azonosító jelzet, vagy a szabványcímben előforduló kulcsszó szerinti keresés:


ICS (a szabványok nemzetközi osztályozási rendszere) szerinti keresés

Nettó ár: 20030 Ft
Kosárba tesz
Alapadatok
Hivatkozási szám
MSZ EN 1366-8:2025
Dokumentumazonosító
185529
Cím
Épületgépészeti berendezések tűzállósági vizsgálatai. 8. rész: Hő- és füstelvezető légcsatornák
Angol cím
Fire resistance tests for service installations. Part 8: Smoke extraction ducts
Alkalmazási terület
This document specifies a test method for determining the fire resistance of smoke extraction ducts. It is applicable only to smoke extraction ducts that pass through another fire compartment apart from the compartment from where smoke needs to be extracted in case of fire. It represents fire exposure of a fully developed fire. This method of test is only applicable to fire resistant ventilation ducts (same construction) with the following classification according to EN 13501-3: - fire from inside and outside i - o; - applicable to a pressure difference up to 500 Pa in fire conditions; NOTE 1 It is assumed that the duct A test(s) in accordance with EN 1366-1 has been performed with an under-pressure of minimum 500 Pa. - with integrity (E) and insulation (I) criteria equal to or higher than the intended classification for the smoke extraction duct. For the purposes of the test described in this document, the duct is referred to as duct C. This test method has been designed to cover both vertical and horizontal smoke extraction ducts. A vertical system need not be evaluated to this method provided that: - both horizontal (ho) and vertical (ve) classification according to EN 13501-3 has been obtained for the ventilation duct; - it has been tested in a horizontal orientation to this method. If the ventilation duct in practise is only used for vertical applications in smoke extraction systems, only vertical (ve) classification is obtained in accordance with EN 13501-3 and tested only in a vertical orientation to this test method. This test method is suitable for ducts constructed from non-combustible materials (class A1 and A2-s1, d0 according to EN 13501-1). NOTE 2 Reaction with components of the duct can affect the oxygen concentration inside the duct leading to inaccurate calculation of the leakage rate. If it is determined this has happened refer to Annex D. This document applies to four sided rectangular and circular ducts only (with fire exposure on all sides). Ducts that utilize elements of construction for one, two or three sides are not covered. An alternative test method for one, two and three sided ducts will be developed separately.
ICS
13.220.20 Tűzvédelem
13.220.50 Építőanyagok és -elemek tűzállósága
A szabvány nyelve
angol
Az érvényesség kezdete
2025-04-01
További adatok
Forrás
idt EN 1366-8:2024
Utód
Módosítás
Kiegészítő információk
SZK-közlemények
Kapcsolódó európai jogszabály
305/2011/EU; (CPR11)
Kereskedelmi adatok
A szabvány
kapható formátuma
Papír ,
PDF (letöltés) (a fájl mérete: 4705995) ,
oldalszáma
59 oldal; U kategória
ára
Nettó: 20030 Ft
Bruttó:
Papír formátum esetén (20% nyomdai költséggel, 5% Áfával): 25238 Ft
PDF (letöltés) formátum esetén ( 27% Áfával): 25438 Ft
Szabvány életútja
Megtekintett szabvány

MSZ EN 1366-8:2025

2025-04-01

Utódok

Jelenleg nincsenek utódok