Hivatkozási szám, azonosító jelzet, vagy a szabványcímben előforduló kulcsszó szerinti keresés:

ICS (a szabványok nemzetközi osztályozási rendszere) szerinti keresés

Nettó ár: 10890 Ft
Kosárba tesz
Hivatkozási szám
MSZ EN 50470-3:2022
Villamos fogyasztásmérő berendezések. 3. rész: Kiegészítő követelmények. Elektronikus fogyasztásmérők hatásos, váltakozó áramú teljesítmény mérésére (A, B és C pontossági osztály)
Angol cím
Electricity metering equipment. Part 3: Particular requirements. Static meters for AC active energy (class indexes A, B and C)
Alkalmazási terület
This document applies only to static watt-hour meters of accuracy classes A, B and C for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests. NOTE 1 For general requirements, such as construction, EMC, safety, dependability etc., see the relevant EN 62052 series or EN 62059 series. This document applies to electricity metering equipment designed to: — measure and control electrical energy on electrical networks (mains) with voltage up to 1 000 V AC; NOTE 2 For AC electricity meters, the voltage mentioned above is the line-to-neutral voltage derived from nominal voltages. See EN 62052-31:2016, Table 7. EN 62052-31:2016 covers AC voltages only up to 600 V and Ed. 2 of EN IEC 62052-31 will cover AC voltages up to 1000 V. — have all functional elements, including add-on modules, enclosed in, or forming a single meter case with exception of indicating displays; — operate with integrated or detached indicating displays; — be installed in specified matching sockets or racks; — optionally, provide additional functions other than those for measurement of electrical energy. Meters designed for operation with low power instrument transformers (LPITs as defined in the EN 61869 series) can be tested for compliance with this document only if such meters and their LPITs are tested together and meet the requirements for directly connected meters. NOTE 3 Modern electricity meters typically contain additional functions such as measurement of voltage magnitude, current magnitude, power, frequency, power factor, etc.; measurement of power quality parameters; load control functions; delivery, time, test, accounting, recording functions; data communication interfaces and associated data security functions. The relevant standards for these functions could apply in addition to the requirements of this document. However, the requirements for such functions are outside the scope of this document. NOTE 4 Product requirements for power metering and monitoring devices (PMDs) and measurement functions such as voltage magnitude, current magnitude, power, frequency, etc., are covered in EN 61557-12:2008. However, devices compliant with EN 61557-12:2008 are not intended to be used as billing meters unless they are also compliant with the EN IEC 62052-11:2021/A11:2022 and EN 50470-3:2022 standards. NOTE 5 Product requirements for power quality instruments (PQIs) are covered in EN 62586-1:2017. Requirements for power quality measurement techniques (functions) are covered in EN 61000-4-30:2015. Requirements for testing of the power quality measurement functions are covered in EN 62586-2:2017. This document does not apply to: — meters for which the line-to-neutral voltage derived from nominal voltages exceeds 1 000 V AC; — meters intended for connection with low power instrument transformers (LPITs as defined in the EN 61869 series) when tested without such transformers; — metering systems comprising multiple devices (except of LPITs) physically remote from one another; — portable meters; NOTE 6 Portable meters are meters that are not permanently connected. — meters used in rolling stock, vehicles, ships and airplanes; — laboratory and meter test equipment; — reference standard meters; — data interfaces to the register of the meter; — matching sockets or racks used for installation of electricity metering equipment; — any additional functions provided in electrical energy meters. This document does not cover measures for the detection and prevention of fraudulent attempts to compromise meter’s performance (tampering). NOTE 7 Nevertheless, specific tampering detection and prevention requirements, and test methods, as relevant for a particular market are subject to the agreement between the manufacturer and the purchaser. NOTE 8 Specifying requirements and test methods for fraud detection and prevention would be counterproductive, as such specifications would provide guidance for potential fraudsters. NOTE 9 There are many types of meter tampering reported from various markets; therefore, designing meters to detect and prevent all types of tampering could lead to unjustified increase in costs of meter design, verification and validation. NOTE 10 Billing systems, such as smart metering systems, are capable of detecting irregular consumption patterns and irregular network losses which enable discovery of suspected meter tampering. NOTE 11 For transformer operated meters paired with current transformers (CTs) according to EN 61869-2: the standard CT measuring range is specified from 0,05 In to Imax for accuracy classes 0,1, 0,2, 0,5 and 1 and these CTs are used for meters of class C, B and A according to this document. NOTE 12 This document does not specify emission requirements, these are specified in EN IEC 62052-11:2021/A11:2022, 9.3.14.
91.140.50 Villamosenergia-ellátó rendszerek
A szabvány nyelve
Az érvényesség kezdete
További adatok
idt EN 50470-3:2022
Kapcsolódó európai jogszabály
2014/32/EU (MID14)
Kereskedelmi adatok
A szabvány
kapható formátuma
Papír ,
PDF (letöltés) (a fájl mérete: 643886) ,
30 oldal; P kategória
Nettó: 10890 Ft
Papír formátum esetén (5% Áfával): 13721 Ft
PDF (letöltés) formátum esetén (27% Áfával): 13830 Ft
Szabvány életútja
Megtekintett szabvány

MSZ EN 50470-3:2022



Jelenleg nincsenek utódok