Szabványkereső

Hivatkozási szám, azonosító jelzet, vagy a szabványcímben előforduló kulcsszó szerinti keresés:


ICS (a szabványok nemzetközi osztályozási rendszere) szerinti keresés

Nettó ár: 8640 Ft
Kosárba tesz
Alapadatok
Hivatkozási szám
MSZ EN IEC 61215-1-1:2021
Dokumentumazonosító
177277
Cím
Földi alkalmazású, fotovillamos (PV-) modulok. A szerkezeti felépítés minősítése és típusjóváhagyás. 1-1. rész: Kristályos szilícium fotovillamos (PV-) modulok különleges vizsgálati követelményei (IEC 61215-1-1:2021)
Angol cím
Terrestrial photovoltaic (PV) modules. Design qualification and type approval. Part 1-1: Special requirements for testing of crystalline silicon photovoltaic (PV) modules (IEC 61215-1-1:2021)
Alkalmazási terület
This document lays down requirements for the design qualification of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. The useful service life of modules so qualified will depend on their design, their environment and the conditions under which they are operated. Test results are not construed as a quantitative prediction of module lifetime. In climates where 98th percentile operating temperatures exceed 70 °C, users are recommended to consider testing to higher temperature test conditions as described in IEC TS 63126. Users desiring qualification of PV products with lesser lifetime expectations are recommended to consider testing designed for PV in consumer electronics, as described in IEC 63163 (under development). Users wishing to gain confidence that the characteristics tested in IEC 61215 appear consistently in a manufactured product may wish to utilize IEC 62941 regarding quality systems in PV manufacturing. This document is intended to apply to all crystalline silicon terrestrial flat plate modules. This document does not apply to modules used with concentrated sunlight although it may be utilized for low concentrator modules (1 to 3 suns). For low concentration modules, all tests are performed using the irradiance, current, voltage and power levels expected at the design concentration. The objective of this test sequence is to determine the electrical characteristics of the module and to show, as far as possible within reasonable constraints of cost and time, that the module is capable of withstanding prolonged exposure outdoors. Accelerated test conditions are empirically based on those necessary to reproduce selected observed field failures and are applied equally across module types. Acceleration factors may vary with product design and thus not all degradation mechanisms may manifest. Further general information on accelerated test methods including definitions of terms may be found in IEC 62506. Some long-term degradation mechanisms can only reasonably be detected via component testing, due to long times required to produce the failure and necessity of stress conditions that are expensive to produce over large areas. Component tests that have reached a sufficient level of maturity to set pass/fail criteria with high confidence are incorporated into the IEC 61215 series via addition to Table 1 in IEC 61215-1:2021. In contrast, the tests procedures described in this series, in IEC 61215-2, are performed on modules. This document defines PV technology dependent modifications to the testing procedures and requirements per IEC 61215-1:2021 and IEC 61215-2:2021.
ICS
27.160 Napenergia
A szabvány nyelve
angol
Az érvényesség kezdete
2021-08-01
További adatok
Forrás
idt EN IEC 61215-1-1:2021; idt IEC 61215-1-1:2021
Utód
Módosítás
Kiegészítő információk
SZK-közlemények
Kapcsolódó európai jogszabály
Kereskedelmi adatok
A szabvány
kapható formátuma
Papír ,
PDF (letöltés) (a fájl mérete: 743389) ,
oldalszáma
15 oldal; H kategória
ára
Nettó: 8640 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 10886 Ft
PDF (letöltés) formátum esetén (27% Áfával): 10973 Ft
Szabvány életútja
Megtekintett szabvány

MSZ EN IEC 61215-1-1:2021

2021-08-01

Utódok

Jelenleg nincsenek utódok