Szabványkereső

Hivatkozási szám, azonosító jelzet, vagy a szabványcímben előforduló kulcsszó szerinti keresés:


ICS (a szabványok nemzetközi osztályozási rendszere) szerinti keresés

Nettó ár: 33350 Ft
Kosárba tesz
Alapadatok
Hivatkozási szám
MSZ EN IEC 61800-3:2019
Dokumentumazonosító
170541
Cím
Szabályozható fordulatszámú villamos hajtásrendszerek. 3. rész: EMC-követelmények és egyedi vizsgálati módszerek (IEC 61800-3:2017)
Angol cím
Adjustable speed electrical power drive systems. Part 3: EMC requirements and specific test methods (IEC 61800-3:2017)
Alkalmazási terület
This part of IEC 61800 specifies electromagnetic compatibility (EMC) requirements for power drive systems (PDSs, defined in 3.1). These are adjustable speed AC or DC motor drives. Requirements are stated for PDSs with converter input and/or output voltages (line-to-line voltage), up to 35 kV AC RMS. PDSs covered by this document are those installed in residential, commercial and industrial locations with the exception of traction applications, and electric vehicles. PDSs can be connected to either industrial or public power distribution networks. Industrial networks are supplied by a dedicated distribution transformer, which is usually adjacent to or inside the industrial location, and supplies only industrial customers. Industrial networks can also be supplied by their own electric generating equipment. On the other hand, PDSs can be directly connected to low-voltage public mains networks which also supply residential premises, and in which the neutral is generally earthed (grounded). The scope of this part of IEC 61800, related to EMC, includes a broad range of PDSs from a few hundred watts to hundreds of megawatts. PDSs are often included in a larger system. The system aspect is not covered by this document but guidance is provided in the informative annexes. The requirements have been selected so as to ensure EMC for PDSs at residential, commercial and industrial locations. The requirements cannot, however, cover extreme cases which can occur with an extremely low probability. Changes in the EMC behaviour of a PDS, as a result of fault conditions, are not taken into account. The object of this document is to define the limits and test methods for a PDS according to its intended use. This document includes immunity requirements and requirements for electromagnetic emissions. NOTE 1 Emission can cause interference in other electronic equipment (for example radio receivers, measuring and computing devices). Immunity is meant to protect the equipment from continuous and transient conducted and radiated disturbances including electrostatic discharges. The emission and immunity requirements are balanced against each other and against the actual environment of the PDS. This document defines the minimum EMC requirements for a PDS. Immunity requirements are given according to the environment classification. Low-frequency emission requirements are given according to the nature of the supply network. Highfrequency emission requirements are given according to four categories of intended use, which cover both environment and bringing into operation. As a product standard, this document can be used for the assessment of PDS. It can also be used for the assessment of complete drive modules (CDM) or basic drive modules (BDM) (see 3.1), which can be marketed separately. This document contains • conformity assessment requirements for products to be placed on the market, and • recommended engineering practice (see 6.5) for cases where high frequency emissions cannot be measured before the equipment is placed on the market (such PDSs are defined in 3.2.7 as category C4). NOTE 2 The first edition of IEC 61800-3 identified that the intended use could require engineering for putting into service. This was done by the “restricted distribution mode”. Equipment formerly identified under “restricted distribution mode” is now covered by categories C2 and C4 (see 3.2). This document is intended as a complete EMC product standard for the EMC conformity assessment of products of categories C1, C2 and C3, when placing them on the market (see definitions 3.2.4 to 3.2.6). Radio frequency emission of equipment of category C4 is only assessed when it is installed in its intended location. It is therefore treated as a fixed installation, for which this document gives rules of engineering practice in 6.5 and Annex E, although it gives no defined emission limits (except in case of complaint). This document does not specify any safety requirements for the equipment such as protection against electric shocks, insulation co-ordination and related dielectric tests, unsafe operation, or unsafe consequences of a failure. It also does not cover safety and functional safety implications of electromagnetic phenomena. In special cases, when highly susceptible apparatus is being used in proximity, additional mitigation measures can have to be employed to reduce the electromagnetic emission further below the specified levels or additional countermeasures can have to be employed to increase the immunity of the highly susceptible apparatus. As an EMC product standard for PDSs, this document takes precedence over all aspects of the generic standards, and no additional EMC tests are performed. If a PDS is included as part of equipment covered by a separate EMC product standard, the EMC standard of the complete equipment applies.
ICS
29.200 Egyenirányítók. Áramátalakítók. Stabilizált tápegységek
33.100 Elektromágneses összeférhetőség (EMC)
A szabvány nyelve
angol
Az érvényesség kezdete
2019-01-01
A visszavonás napja
2026-08-09
További adatok
Forrás
idt EN IEC 61800-3:2018; idt IEC 61800-3:2017
Módosítás
Kiegészítő információk
SZK-közlemények
Kapcsolódó európai jogszabály
2014/30/EU (EMC14); 2004/108/EK; (EMC04)
Kereskedelmi adatok
A szabvány
kapható formátuma
Papír ,
PDF (letöltés) (a fájl mérete: 1812861) ,
oldalszáma
127 oldal; XD kategória
ára
Nettó: 33350 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 42021 Ft
PDF (letöltés) formátum esetén (27% Áfával): 42355 Ft
Szabvány életútja
Megtekintett szabvány

MSZ EN IEC 61800-3:2019

2019-01-01 - 2026-08-09