Hivatkozási szám

MSZ EN 13242:2013

Dokumentumazonosító

156640

Cím

Kőanyaghalmazok műtárgyakban és útépítésben használt, kötőanyag nélküli és hidraulikus kötőanyagú anyagokhoz

Angol cím

Aggregates for unbound and hydraulically bound materials for use in civil engineering work and road construction

Alkalmazási terület

This European Standard specifies the properties of aggregates and filler aggregates obtained by processing natural, manufactured or recycled materials and mixtures of these aggregates for use in hydraulically bound and unbound materials for civil engineering works and road constructions. It covers aggregates having an oven dried particle density greater than 2,0 Mg/m3 (2000Kg/m3). It also covers recycled aggregates with particle densities greater than 1,50 Mg/m3 (1 500 kg/m3) with appropriate caveats and recycled fine aggregate with appropriate caveats. A list of the source materials that have been considered and indicating those which are within the scope of this standard is given in Annex A (normative). Requirements for the evaluation of conformity of the products to this European Standard are given in EN 16236. It incorporates a general requirement that aggregates will not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination. The tables in this standard include categories which are common across the four main aggregate standards: EN 12620, EN 13043, EN 13139 and EN 13242. Not all of these categories are appropriate for aggregates for use in hydraulically bound and unbound materials for civil engineering works and road constructions. Categories, notes, comments etc, which are shown grey shaded should not be used for aggregates for use in hydraulically bound and unbound materials for civil engineering works and road constructions. Aggregates used in construction should comply with all the requirements of the relevant European Standards for aggregates. These standards include comprehensive and specific requirements for natural aggregates, iron and steel making slag and recycled aggregates, dealing with, for example, the stability of certain basalts, the expansion of certain slags and the constitution of recycled aggregates. For materials from some other secondary sources, however, work is ongoing and the requirements are incomplete. In the meantime, such materials, when placed on the market as aggregates, should conform fully to this standard but may also be required to conform to specific relevant additional requirements at the place of use. Additional characteristics and requirements may be specified on a case by case basis depending upon experience of use of the product, and defined in specific contractual documents. NOTE 1 Requirements for lightweight aggregates are specified in prEN 13055. Requirements for the declaration of the potential of aggregates to release regulated dangerous substances are currently under development. Until such time as these are finalised, attention should be paid to requirements at the place of use. NOTE 2 Requirements for hydraulically bound and unbound materials for civil engineering works are specified in EN 13285 and are not therefore covered in this standard. EN 13285 does however call up the general requirements of EN 13242 for the aggregates.

ICS

91.100.15 Ásványi anyagok és termékek

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2013-09-01

A visszavonás napja

2014-05-01

Forrás

idt EN 13242:2013

Előd

MSZ EN 13242:2002+A1:2008

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

2014/01: Közlemény

Kapcsolódó európai jogszabály

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 382422) ,

oldalszáma

47 oldal; T kategória

ára

Nettó: 15850 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 19971 Ft
PDF (letöltés) formátum esetén (27% Áfával): 20130 Ft