Hivatkozási szám

MSZ EN 302 878-3:2012

Dokumentumazonosító

153466

Cím

Hozzáférés, végberendezések, átvitel és nyalábolás. Interaktív kábeltelevíziós szolgáltatás harmadik generációs átviteli rendszerei. IP-kábelmodem. 3. rész: Letöltési rádiófrekvenciás interfész. DOCSIS 3.0

Angol cím

Access, Terminals, Transmission and Multiplexing (ATTM). Third Generation Transmission Systems for Interactive Cable Television Services - IP Cable Modems. Part 3: Downstream Radio Frequency Interface. DOCSIS 3.0

Alkalmazási terület

The present document defines the RF characteristics required in the downstream transmitter(s) of DOCSIS 3.0 CMTSs and EQAMs, sufficiently enough to permit vendors to build devices that meet the needs of cable operators around the world. In addition to defining these requirements for a DOCSIS 3.0 device, the present document could also be applicable to other devices such as: • an Edge QAM (EQAM) not being used for DOCSIS 3.0 services; or • an integrated Cable Modem Termination System (CMTS) with multiple downstream channels per RF port previous to DOCSIS 3.0. There are differences in the cable spectrum planning practices adopted for different networks in the world. Therefore two options for physical layer technology are included, which have equal priority and are not required to be interoperable. One technology option is based on the downstream multi-program television distribution that is deployed in North America using 6 MHz channelling. The other technology option is based on the corresponding European multi-program television distribution. Both options have the same status, notwithstanding that the document structure does not reflect this equal priority. The first of these options is defined in clauses 5, 6 and 7, whereas the second is defined by replacing the content of those clauses with the content of annex A. Correspondingly, [4] and [2] apply only to the first option, and EN 300 429 [8] only to the second. Compliance with the present document requires compliance with the one or the other of these implementations, not with both. It is not required that equipment built to one option will interoperate with equipment built to the other. A DRFI-compliant device may be a single-channel only device, or it may be a multiple-channel device capable of generating one or multiple downstream RF carriers simultaneously on one RF output port. An EQAM may be a module of a modular cable modem termination system (M-CMTS) and be used for delivering a high-speed data service or it may serve as a component of a digital video or Video-on-Demand (VoD) system, delivering high quality digital video to subscribers. These specifications are crafted to enable an EQAM to be used without restriction in either or both service delivery scenarios simultaneously. "Simultaneous" in the early deployments means that if a RF output port has multiple QAM channels, some channel(s) may be delivering high-speed data while some other channel(s) may be delivering digital video. The present document enables future uses, wherein a single QAM channel may share bandwidth between high-speed data and digital video in the same MPEG transport stream. Conceptually, an EQAM will accept input via an Ethernet link, integrate the incoming data into an MPEG transport stream, modulate one of a plurality of RF carriers, per these specifications, and deliver the carrier to a single RF output connector shared in common with all modulators. Conceivably, a single EQAM RF channel could be used for data and video simultaneously. The reason that an EQAM RF channel can be used for either is that both digital video and DOCSIS data downstream channels are based on ITU-T Recommendation J.83 [4], annex B for cable networks in North America and EN 300 429 [8] for cable networks deployed in Europe. On downstream channels complying to ITU-T Recommendation J.83 [4], annex B, typically, the only difference between an EQAM RF channel operating in a video mode and an EQAM RF channel operating in DOCSIS data mode is the interleaver depth (see clauses 6.3.1 and 6.3.3). DOCSIS data runs in a low latency mode using a shallow interleaver depth at the cost of some burst protection. DOCSIS data can do this because if a transmission error occurs, the higher layer protocols will request re-transmission of the missing data. For video, the sequence of frames in the program is both time sensitive and order sensitive and cannot be re-transmitted. For this reason, video uses a deeper interleaver depth to provide more extensive burst protection and deliver more of the program content without loss. The penalty video pays is in latency. The entire program content is delayed by a few milliseconds, typically, and is invisible to the viewers of the program. The conflicting demands for interleaver depth are what prevent a single EQAM RF channel from being used optimally for video and DOCSIS data simultaneously. A traditional integrated CMTS, however, is used solely for DOCSIS data.

ICS

33.040.01 Távközlési rendszerek általában

33.060.40 Kábeles elosztórendszerek

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2012-04-01

Forrás

idt EN 302 878-3:2011-11

Előd

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

Kapcsolódó európai jogszabály

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 528195) ,

oldalszáma

60 oldal; U kategória

ára

Nettó: 17420 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 21949 Ft
PDF (letöltés) formátum esetén (27% Áfával): 22123 Ft