Hivatkozási szám

MSZ EN 13476-1:2026

Dokumentumazonosító

187607

Cím

Műanyag csővezetékrendszerek nyomás nélküli, föld alatti alagcsövezéshez és csatornázáshoz. Kemény poli(vinil-klorid) (PVC-U), polipropilén (PP) és polietilén (PE) strukturált falú csővezetékrendszerek. 1. rész: Általános követelmények és teljesítményjellemzők

Angol cím

Plastics piping systems for non-pressure underground drains and sewers. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Part 1: General requirements and performance characteristics

Alkalmazási terület

This document, together with EN 13476-2 and EN 13476-3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended for use in non-pressure underground drains and sewers for foul wastewater. NOTE 1 Products complying with this document can also be used in non-pressure underground drains and sewers for surface water. This document is applicable to: a) structured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by “U”; b) structured-wall pipes and fittings, which are to be used buried in ground both outside (application area code “U”) and within a building structure (application area code “D”); reflected in the marking of products by “UD”. In conjunction with EN 13476-2 and EN 13476-3, it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where EN 13476-2 and EN 13476-3 provide options. EN 13476-2 and EN 13476-3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B, respectively. This document, together with EN 13476-2 and EN 13476-3, is applicable to a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 3 Pipes, fittings and other components conforming to any plastic product standards referred to in Clause 2 can be used with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in EN 13476-2 and to the performance requirements given in Clause 9.

ICS

23.040.01 Csővezetékek és elemeik általában

93.030 Külső szennyvízrendszerek

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2026-04-01

Forrás

idt EN 13476-1:2025

Előd

MSZ EN 13476-1:2018

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

Kapcsolódó európai jogszabály

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 1473469) ,

oldalszáma

32 oldal; P kategória

ára

Nettó: 16560 Ft
Bruttó:
Papír formátum esetén (25% nyomdai költséggel, 5% Áfával): 21735 Ft
PDF (letöltés) formátum esetén ( 27% Áfával): 21031 Ft