Hivatkozási szám

MSZ EN IEC 60669-2-1:2023

Dokumentumazonosító

181005

Cím

Kapcsolók háztartási és hasonló jellegű, rögzített villamos szerelésekhez. 2-1. rész: Kiegészítő követelmények. Elektronikus vezérlőkészülékek (IEC 60669-2-1:2021)

Angol cím

Switches for household and similar fixed electrical installations. Part 2-1: Particular requirements. Electronic control devices (IEC 60669-2-1:2021)

Alkalmazási terület

This clause of Part 1 is completely replaced by the following: This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units. It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors. It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons. This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF. Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices. This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls). The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed: – intentionally by a person via an actuating member, a key, a card, etc., via a sensing surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal; – by physical means, for example, light, temperature, humidity, time, wind velocity, presence of people; – by any other influence. This document also applies to electronic control devices which include integrated radio receivers and transmitters. This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices. Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670. Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of -5 °C. NOTE 1 For lower temperatures, see Annex E. Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices. In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required. This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1. Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA. Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC. Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE. NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.

ICS

29.120.40 Kapcsolók

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2023-02-01

Forrás

idt EN IEC 60669-2-1:2022/AC:2024; idt EN IEC 60669-2-1:2022; idt IEC 60669-2-1:2021

Előd

MSZ EN 60669-2-1:2005, MSZ EN 50428:2005, MSZ EN 50428:2005/A1:2008, MSZ EN 60669-2-1:2004/A1:2010, MSZ EN 50428:2005/A2:2010, MSZ EN 60669-2-1:2004/A12:2011, MSZ EN 60669-2-5:2017

Utód

Módosítás

MSZ EN IEC 60669-2-1:2022/A11:2023

Kiegészítő információk

SZK-közlemények

2024/03: Helyesbítés

Kapcsolódó európai jogszabály

2014/35/EU (LVD14); 2014/53/EU (RTTE14); 2014/30/EU (EMC14)

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 3155312) ,

oldalszáma

140 oldal; XD kategória

ára

Nettó: 33350 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 42021 Ft
PDF (letöltés) formátum esetén (27% Áfával): 42355 Ft