Hivatkozási szám

MSZ EN ISO 14577-4:2017

Dokumentumazonosító

164687

Cím

Fémek. A keménység és az anyagjellemzők műszeres, benyomódásos rendszerű mérése. 4. rész: Fémes és nemfémes bevonatok mérési módszere (ISO 14577-4:2016)

Angol cím

Metallic materials. Instrumented indentation test for hardness and materials parameters. Part 4: Test method for metallic and non-metallic coatings (ISO 14577-4:2016)

Alkalmazási terület

This part of ISO 14577 specifies a method for testing coatings which is particularly suitable for testing in the nano/micro range applicable to thin coatings. However, the application of this method of this part of ISO 14577 is not needed if the indentation depth is such a small fraction of the coating thickness that in any possible case a substrate influence can be neglected and the coating can be considered as a bulk material. Limits for such cases are given. This test method is limited to the examination of single layers when the indentation is carried out normal to the test piece surface, but graded and multilayer coatings can also be measured in cross-section if the thickness of the individual layers or gradations is greater than the spatial resolution of the indentation process. The test method is not limited to any particular type of material. Metallic and non-metallic coatings are included in the scope of this part of ISO 14577. In this part of ISO 14577, the term coating is used to refer to any solid layer with homogeneous properties different to that of a substrate it is connected to. The method assumes that coating properties are constant with indentation depth. Composite coatings are considered to be homogenous if the structure size is less than the indentation size. The application of this part of ISO 14577 regarding measurement of indentation hardness is only possible if the indenter is a pyramid or a cone with a radius of tip curvature small enough for plastic deformation to occur within the coating. The hardness of visco-elastic materials or materials exhibiting significant creep will be strongly affected by the time taken to perform the test. NOTE 1 ISO 14577-1, ISO 14577-2 and ISO 14577-3 define usage of instrumented indentation testing of bulk materials over all force and displacement ranges. NOTE 2 The analysis used here does not make any allowances for pile-up or sink-in of indents. Use of Atomic Force Microscopy (AFM) to assess the indent shape allows the determination of possible pile-up or sink-in of the surface around the indent. These surface effects result in an under-estimate (pile-up) or over-estimate (sink-in) of the contact area in the analysis and hence may influence the measured results. Pile-up generally occurs for fully work-hardened materials. Pile-up of soft, ductile materials is more likely for thinner coatings due to the constraint of the stresses in the zone of plastic deformation in the coating. It has been reported that the piled up material results in an effective increase of the contact area for the determination of hardness, while the effect is less pronounced for the determination of indentation modulus, since the piled up material behaves less rigidly.[1][2]

ICS

77.040.10 Fémek mechanikai vizsgálata

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2017-03-01

Forrás

idt ISO 14577-4:2016; idt EN ISO 14577-4:2016

Előd

MSZ EN ISO 14577-4:2007

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

Kapcsolódó európai jogszabály

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 1207860) ,

oldalszáma

28 oldal; N kategória

ára

Nettó: 11980 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 15095 Ft
PDF (letöltés) formátum esetén (27% Áfával): 15215 Ft