Hivatkozási szám

MSZ EN 60695-11-20:2015

Dokumentumazonosító

161983

Cím

A tűzveszélyesség vizsgálata. 11-20. rész: Vizsgálólángok. Vizsgálati módszerek 500 W-os lánggal (IEC 60695-11-20:2015)

Angol cím

Fire hazard testing. Part 11-20: Test flames. 500 W flame test methods (IEC 60695-11-20:2015)

Alkalmazási terület

This part of IEC 60695 describes a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products. Vertically oriented bar specimens or horizontally oriented plate test specimens are exposed to a small flame ignition source with a nominal thermal power of 500 W. The test method uses two test specimen configurations to classify material performance. Rectangular bar-shaped test specimens are used to assess ignitability and burning behaviour, and square plate test specimens are used to assess the resistance of the test specimen to burn-through, as defined in 8.3.3. This test method only applies to materials that have been classified as V-0 or V-1 according to IEC 60695-11-10. This test method is only applicable to solid and cellular materials that have an apparent density of more than 250 kg/m3, determined in accordance with ISO 845. The method does not apply to materials that shrink away from the applied flame without igniting due to their thinness. The test method described provides classifications which may be used for quality assurance, the pre-selection of component materials of products, or to verify the required minimum flammability classification of materials used in end products. If used for pre-selection, then positive results shall be obtained at a test specimen thickness which equals the smallest thickness used in the product application. The results obtained provide some information about the behaviour of materials in service, but cannot by themselves assure safe performance in service. NOTE 1 Guidance on pre-selection is given in IEC 60695-1-30 [3]1. NOTE 2 Test results are influenced by material additives, e.g. pigments, fillers, and fire retardants, and properties such as the direction of anisotropy and the molecular mass. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

ICS

13.220.40 Anyagok és termékek gyúlékonysága és égési viselkedése

29.020 Elektrotechnika általában

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2015-12-01

Forrás

idt IEC 60695-11-20:2015; idt EN 60695-11-20:2015; idt EN 60695-11-20:2015/AC:2016; idt IEC 60695-11-20:2015/COR1:2016-01

Előd

MSZ EN 60695-11-20:2000, MSZ EN 60695-11-20:1999/A1:2003

Utód

Módosítás

Kiegészítő információk

Az MSZ EN 61300-2-36:1998 helyett alkalmazható.

SZK-közlemények

2016/04: Helyesbítés

Kapcsolódó európai jogszabály

2006/95/EK; (LVD06)

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 1060729) ,

oldalszáma

35 oldal; Q kategória

ára

Nettó: 13160 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 16582 Ft
PDF (letöltés) formátum esetén (27% Áfával): 16713 Ft