Hivatkozási szám

MSZ EN 60947-4-3:2015

Dokumentumazonosító

159765

Cím

Kisfeszültségű kapcsoló- és vezérlőkészülékek. 4-3. rész: Kontaktorok és motorvédő kapcsolók. Váltakozó áramú, félvezetős vezérlők és kontaktorok nem motoros terhelésekhez (IEC 60947-4-3:2014)

Angol cím

Low-voltage switchgear and controlgear. Part 4-3: Contactors and motor-starters. AC semiconductor controllers and contactors for non-motor loads (IEC 60947-4-3:2014)

Alkalmazási terület

This part of IEC 60947 applies to a.c. semiconductor non-motor load controllers and contactors intended for performing electrical operations by changing the state of a.c. electric circuits between the ON-state and the OFF-state. Typical applications are classified by utilization categories given in Table 2. As controllers, they may be used to reduce the amplitude of the r.m.s. a.c. voltage on the load terminals from that of the applied voltage – either continuously or for a specified period of time. The half-wave period of the a.c. wave form remains unchanged from that of the applied voltage. They may include a series mechanical switching device and are intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. This standard characterizes controllers and contactors for use with or without bypass switching devices. The semiconductor controllers and contactors dealt with in this standard are not normally intended to interrupt short-circuit currents. Therefore, suitable short-circuit protection (see 8.2.5) should form part of the installation but not necessarily of the controller itself. In this context, this standard gives requirements for semiconductor controllers and contactors associated with separate short-circuit protective devices. This standard does not apply to: - operation of a.c. and d.c. motors; - low-voltage a.c. semiconductor motor controllers and starters covered by IEC 60947-4-2; - electronic a.c. power controllers covered by the IEC 60146 series; - all-or-nothing solid-state relays. Contactors and control-circuit devices used in semiconductor controllers and contactors should comply with the requirements of their relevant product standard. Where mechanical switching devices are used, they should meet the requirements of their own IEC product standard and the additional requirements of this standard. The object of this standard is to state a) the characteristics of semiconductor controllers and contactors and associated equipment; b) the conditions with which semiconductor controllers and contactors should comply with reference to: - their operation and behaviour; - their dielectric properties; - the degrees of protection provided by their enclosures, where applicable; - their construction; c) the tests intended for confirming that these conditions have been met, and the methods to be adopted for these tests; d) the information to be given with the equipment or in the manufacturer's literature.

ICS

29.130.20 Kisfeszültségű kapcsoló- és vezérlőberendezések

31.180 Nyomtatott áramkörök és lapok

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2015-04-01

Forrás

idt EN 60947-4-3:2014; idt IEC 60947-4-3:2014

Előd

MSZ EN 60947-4-3:2000, MSZ EN 60947-4-3:2000/A1:2007, MSZ EN 60947-4-3:2000/A2:2012

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

Kapcsolódó európai jogszabály

2004/108/EK; (EMC04); 2014/35/EU (LVD14); 2014/30/EU (EMC14); 2006/95/EK; (LVD06)

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 810431) ,

oldalszáma

80 oldal; W kategória

ára

Nettó: 19470 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 24532 Ft
PDF (letöltés) formátum esetén (27% Áfával): 24727 Ft