Hivatkozási szám

MSZ EN ISO 11148-7:2013

Dokumentumazonosító

155013

Cím

Nem villamos hajtású motoros kéziszerszámok. Biztonsági követelmények. 7. rész: Köszörűgépek

Angol cím

Hand-held non-electric power tools. Safety requirements. Part 7: Grinders (ISO 11148-7:2012)

Alkalmazási terület

This part of ISO 11148 specifies safety requirements for hand-held non-electric power tools (hereinafter “grinders”) intended for grinding and cutting-off with abrasive products, for use on all kinds of materials. The grinders can be powered by compressed air or hydraulic fluid and are intended to be used by one operator and supported by the operator’s hand or hands, with or without a suspension, e.g. a balancer. NOTE 1 At the time of publication, no grinders driven by internal combustion engines are known (other than cuttingoff machines within the scope of ISO 19432). Once these are identified, it is intended to amend this part of ISO 11148 to include such power tools. This part of ISO 11148 is applicable to grinders used with: — abrasive products with a peripheral operating speed less than or equal to 80 m/s; — cutting-off wheels with a peripheral operating speed less than or equal to 100 m/s; — abrasive products with an outside nominal diameter less than or equal to 230 mm; — cutting-off wheels with an outside nominal diameter less than or equal to 250 mm; — wire brushes; — diamond and reinforced (segmented) wheels with an outside nominal diameter less than or equal to 450 mm; — flap discs and flap wheels. NOTE 2 For examples of grinders, see Annex B. NOTE 3 Typical abrasive products used together with hand-held grinders are listed in Annex D. This part of ISO 11148 does not cover special requirements and modifications of grinders for the purpose of mounting them in fixtures. This part of ISO 11148 is not applicable to: — die grinders with collets, which are treated in ISO 11148-9; — polishers and sanders (i.e. tools used with coated abrasives except flap discs and flap wheels), which are treated in ISO 11148-8; — cutting-off machines which are driven by internal combustion engines and are used for cutting construction materials, which are treated in ISO 19432; — shaft-mounted wire brushes, which are treated in ISO 11148-9. This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events relevant to grinders when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of grinders in potentially explosive atmospheres. NOTE 4 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.

ICS

25.140.10 Pneumatikus szerszámok

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2013-03-01

Forrás

idt EN ISO 11148-7:2012; idt ISO 11148-7:2012

Előd

MSZ EN 792-7:2001+A1:2009

Utód

Módosítás

Kiegészítő információk

SZK-közlemények

Kapcsolódó európai jogszabály

2006/42/EK AZ EURÓPAI PARLAMENT ÉS A TANÁCS 2006/42/EK IRÁNYELVE (2006. május 17.) a gépekről és a 95/16/EK irányelv módosításáról (átdolgozás) (EGT vonatkozású szöveg) (MAC06)

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 3132234) ,

oldalszáma

61 oldal; V kategória

ára

Nettó: 18390 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 23171 Ft
PDF (letöltés) formátum esetén (27% Áfával): 23355 Ft