Hivatkozási szám

MSZ EN ISO 11960:2005

Dokumentumazonosító

137454

Cím

Kőolaj- és földgázipar. Acélcsövek a kutakhoz béléscsőként vagy termelőcsőként való alkalmazásra (ISO 11960:2004)

Angol cím

Petroleum and natural gas industries. Steel pipes for use as casing or tubing for wells (ISO 11960:2004)

Alkalmazási terület

ISO 11960:2004 specifies the technical delivery conditions for steel pipes (casing, tubing, plain end casing liners and pup joints), coupling stock and accessories and establishes requirements for three Product Specification Levels (PSL-1, PSL-2, PSL-3). The requirements for PSL-1 are the basis of ISO 11960:2004. The requirements that define different levels of standard technical requirements for PSL-2 and PSL-3, for all Grades except H-40 and L-80 9Cr, are contained in Annex H. ISO 11960:2004 is applicable to the following connections in accordance with API Spec 5B: -- short round thread casing (STC); -- long round thread casing (LC); -- buttress thread casing (BC); -- extreme-line casing (XC); -- non-upset tubing (NU); -- external upset tubing (EU); -- integral joint tubing (IJ). For such connections, ISO 11960:2004 specifies the technical delivery conditions for couplings and thread protection. Supplementary requirements that may optionally be agreed for enhanced leak resistance connections are given in Annex A.11 (SR22). ISO 11960:2004 can also be applied to tubulars with connections not covered by ISO/API standards. For pipes covered by ISO 11960:2004, the sizes, masses and wall thicknesses as well as grades and applicable end finishes are given. By agreement between the purchaser and manufacturer, ISO 11960:2004 can also be applied to other plain end pipe sizes and wall thicknesses. The four groups of products to which ISO 11960:2004 is applicable include the following grades of pipe: -- Group 1: All casing and tubing in Grades H, J, K and N; -- Group 2: All casing and tubing in Grades C, L, M and T; -- Group 3: All casing and tubing in Grade P; -- Group 4: All casing in Grade Q. Casing sizes larger than Label 1: 4-1/2 but smaller than Label 1: 10-3/4 may be specified by the purchaser to be used in tubing service. Supplementary requirements that may optionally be agreed between purchaser and manufacturer for non-destructive examination, co

ICS

75.180.10 Kutató-, fúró- és kitermelőberendezések

77.140.75 Acélcsövek és speciális alkalmazású acélcsövek

Műszaki Bizottság

A szabvány nyelve

angol

Az érvényesség kezdete

2005-06-01

A visszavonás napja

2011-11-01

Forrás

idt EN ISO 11960:2004/AC:2007; idt ISO 11960:2004; idt EN ISO 11960:2004

Előd

MSZ EN ISO 11960:2002

Utód

MSZ EN ISO 11960:2011

Módosítás

Kiegészítő információk

SZK-közlemények

2007/09: Helyesbítés

Kapcsolódó európai jogszabály

A szabvány

kapható formátuma

Papír ,
PDF (letöltés) (a fájl mérete: 4067949) ,

oldalszáma

298 oldal; XG kategória

ára

Nettó: 50850 Ft
Bruttó:
Papír formátum esetén (5% Áfával): 64071 Ft
PDF (letöltés) formátum esetén (27% Áfával): 64580 Ft